第1个回答 2011-01-07
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity MINSECONDb is
port(clk,clrm,stop:in std_logic;----时钟/清零信号
secm1,secm0:out std_logic_vector(3 downto 0);----秒高位/低位
co:out std_logic);-------输出/进位信号
end MINSECONDb;
architecture SEC of MINSECONDb is
signal clk1,DOUT2:std_logic;
begin
process(clk,clrm)
variable cnt1,cnt0:std_logic_vector(3 downto 0);---计数
VARIABLE COUNT2 :INTEGER RANGE 0 TO 10 ;
begin
IF CLK'EVENT AND CLK='1'THEN
IF COUNT2>=0 AND COUNT2<10 THEN
COUNT2:=COUNT2+1;
ELSE COUNT2:=0;
DOUT2<= NOT DOUT2;
END IF;
END IF;
if clrm='1' then----当clr为1时，高低位均为0
cnt1:="0000";
cnt0:="0000";
elsif clk'event and clk='1' then
if stop='1' then
cnt0:=cnt0;
cnt1:=cnt1;
end if;
if cnt1="1001" and cnt0="1000" then----当记数为98（实际是经过59个记时脉冲）
co<='1';----进位
cnt0:="1001";----低位为9
elsif cnt0<"1001" then----小于9时
cnt0:=cnt0+1;----计数
--elsif cnt0="1001" then
--clk1<=not clk1;
else
cnt0:="0000";
if cnt1<"1001" then----高位小于9时
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
secm1<=cnt1;
secm0<=cnt0;
end process;
end SEC;
秒模块程序清单
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity SECOND is
port(clk,clr:in std_logic;----时钟/清零信号
sec1,sec0:out std_logic_vector(3 downto 0);----秒高位/低位
co:out std_logic);-------输出/进位信号
end SECOND;
architecture SEC of SECOND is
begin
process(clk,clr)
variable cnt1,cnt0:std_logic_vector(3 downto 0);---计数
begin
if clr='1' then----当ckr为1时，高低位均为0
cnt1:="0000";
cnt0:="0000";
elsif clk'event and clk='1' then
if cnt1="0101" and cnt0="1000" then----当记数为58（实际是经过59个记时脉冲）
co<='1';----进位
cnt0:="1001";----低位为9
elsif cnt0<"1001" then----小于9时
cnt0:=cnt0+1;----计数
else
cnt0:="0000";
if cnt1<"0101" then----高位小于5时
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
sec1<=cnt1;
sec0<=cnt0;
end process;
end SEC;
分模块程序清单
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity MINUTE is
port(clk,en:in std_logic;
min1,min0:out std_logic_vector(3 downto 0);
co:out std_logic);
end MINUTE;
architecture MIN of MINUTE is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clk'event and clk='1' then
if en='1' then
if cnt1="0101" and cnt0="1000" then
co<='1';
cnt0:="1001";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
else
cnt0:="0000";
if cnt1<"0101" then
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
end if;
min1<=cnt1;
min0<=cnt0;
end process;
end MIN;
时模块程序清单
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity HOUR is
port(clk,en:in std_logic;----输入时钟/高电平有效的使能信号
h1,h0:out std_logic_vector(3 downto 0));----时高位/低位
end HOUR;
architecture hour_arc of HOUR is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);----记数
begin
if clk'event and clk='1' then---上升沿触发
if en='1' then---同时“使能”为1
if cnt1="0010" and cnt0="0011" then
cnt1:="0000";----高位/低位同时为0时
cnt0:="0000";
elsif cnt0<"1001" then----低位小于9时，低位记数累加
cnt0:=cnt0+1;
else
cnt0:="0000";
cnt1:=cnt1+1;-----高位记数累加
end if;
end if;
end if;
h1<=cnt1;
h0<=cnt0;
end process;
end hour_arc;
动态扫描模块
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
use ieee.std_logic_arith.all;
entity SELTIME is
port(
clk:in std_logic;------扫描时钟
secm1,secm0,sec1,sec0,min1,min0,h1,h0:in std_logic_vector(3 downto 0);-----分别为秒个位/时位；分个位/
daout:out std_logic_vector(3 downto 0);----------------输出
sel:out std_logic_vector(2 downto 0));-----位选信号
end SELTIME;
architecture fun of SELTIME is
signal count:std_logic_vector(2 downto 0);----计数信号
begin
sel<=count;
process(clk)
begin
if(clk'event and clk='1') then
if(count>="111") then
count<="000";
else
count<=count+1;
end if;
end if;
case count is
when"111"=>daout<= secm0;----秒个位
when"110"=>daout<= secm1;----秒十位
when"101"=>daout<= sec0;----分个位
when"100"=>daout<= sec1;----分十位
when"011"=>daout<=min0; ----时个位
when"010"=>daout<=min1;----时十位
when"001"=>daout<=h0;
when others =>daout<=h1;
end case;
end process;
end fun;
报时模块
library ieee;
use ieee.std_logic_1164.all;
entity ALERT is
port(m1,m0,s1,s0:in std_logic_vector(3 downto 0);------输入秒、分高/低位信号
clk:in std_logic;------高频声控制
q500,qlk:out std_logic);----低频声控制
end ALERT;
architecture sss_arc of ALERT is
begin
process(clk)
begin
if clk'event and clk='1' then
if m1="0101" and m0="1001" and s1="0101" then----当秒高位为5，低位为9时且分高位为5
if s0="0001" or s0="0011" or s0="0101" or s0="0111" then---当分的低位为1或3或5或7时
q500<='1';----低频输出为1
else
q500<='0';----否则输出为0
end if;
end if;
if m1="0101" and m0="1001" and s1="0101" and s0="1001" then---当秒高位为5，低位为9时且分高位为5，----分低位为9时，也就是“59分59秒”的时候“报时”
qlk<='1';-----高频输出为1
else
qlk<='0';
end if;
end if;
end process;
end sss_arc;
显示模块
library ieee;
use ieee.std_logic_1164.all;
entity DISPLAY is
port(d:in std_logic_vector(3 downto 0);----连接seltime扫描部分d信号
q:out std_logic_vector(6 downto 0));----输出段选信号（电平）
end DISPLAY;
architecture disp_are of DISPLAY is
begin
process(d)
begin
case d is
when"0000" =>q<="0111111";--显示0
when"0001" =>q<="0000110";--显示1
when"0010" =>q<="1011011";--显示2
when"0011" =>q<="1001111";--显示3
when"0100" =>q<="1100110";--显示4
when"0101" =>q<="1101101";--显示5
when"0110" =>q<="1111101";--显示6
when"0111" =>q<="0100111";--显示7
when"1000" =>q<="1111111";--显示8
when others =>q<="1101111";--显示9
end case;
end process;
end disp_are;
顶层文件（原理图输入）
********************************************************************
数字钟设计模块与程序（不含秒表）
*********************************************************************
1.分频模块（原理图输入）
2. 秒模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity SECOND is
port(clk,clr:in std_logic;
sec1,sec0:out std_logic_vector(3 downto 0);
co:out std_logic);
end SECOND;
architecture SEC of SECOND is
begin
process(clk,clr)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clr='1' then
cnt1:="0000";
cnt0:="0000";
elsif clk'event and clk='1' then
if cnt1="0101" and cnt0="1000" then
co<='1';
cnt0:="1001";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
else
cnt0:="0000";
if cnt1<"0101" then
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
sec1<=cnt1;
sec0<=cnt0;
end process;
end SEC;
3.分模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity MINUTE is
port(clk,en:in std_logic;
min1,min0:out std_logic_vector(3 downto 0);
co:out std_logic);
end MINUTE;
architecture MIN of MINUTE is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clk'event and clk='1' then
if en='1' then
if cnt1="0101" and cnt0="1000" then
co<='1';
cnt0:="1001";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
else
cnt0:="0000";
if cnt1<"0101" then
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
end if;
min1<=cnt1;
min0<=cnt0;
end process;
end MIN;
4.时模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity HOUR is
port(clk,en:in std_logic;
h1,h0:out std_logic_vector(3 downto 0));
end HOUR;
architecture hour_arc of HOUR is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clk'event and clk='1' then
if en='1' then
if cnt1="0010" and cnt0="0011" then
cnt1:="0000";
cnt0:="0000";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
end if;
end if;
end if;
h1<=cnt1;
h0<=cnt0;
end process;
end hour_arc;
5.扫描模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
use ieee.std_logic_arith.all;
entity SELTIME is
port(
clk:in std_logic;
sec1,sec0,min1,min0,h1,h0:in std_logic_vector(3 downto 0);
daout:out std_logic_vector(3 downto 0);
sel:out std_logic_vector(2 downto 0));
end SELTIME;
architecture fun of SELTIME is
signal count:std_logic_vector(2 downto 0);
begin
sel<=count;
process(clk)
begin
if(clk'event and clk='1') then
if(count>="101") then
count<="000";
else
count<=count+1;
end if;
end if;
case count is
when"000"=>daout<= sec0;
when"001"=>daout<= sec1;
when"010"=>daout<= min0;
when"011"=>daout<= min1;
when"100"=>daout<=h0;
when others =>daout<=h1;
end case;
end process;
end fun;
6.显示模块程序
library ieee;
use ieee.std_logic_1164.all;
entity DISPLAY is
port(d:in std_logic_vector(3 downto 0);
q:out std_logic_vector(6 downto 0));
end DISPLAY;
architecture disp_are of DISPLAY is
begin
process(d)
begin
case d is
when"0000" =>q<="0111111";
when"0001" =>q<="0000110";
when"0010" =>q<="1011011";
when"0011" =>q<="1001111";
when"0100" =>q<="1100110";
when"0101" =>q<="1101101";
when"0110" =>q<="1111101";
when"0111" =>q<="0100111";
when"1000" =>q<="1111111";
when others =>q<="1101111";
end case;
end process;
end disp_are;
7.定时闹钟模块程序
library ieee;
use ieee.std_logic_1164.all;
entity ALERT is
port(m1,m0,s1,s0:in std_logic_vector(3 downto 0);
clk:in std_logic;
q500,qlk:out std_logic);
end ALERT;
architecture sss_arc of ALERT is
begin
process(clk)
begin
if clk'event and clk='1' then
if m1="0101" and m0="1001" and s1="0101" then
if s0="0001" or s0="0011" or s0="0101" or s0="0111" then
q500<='1';
else
q500<='0';
end if;
end if;
if m1="0101" and m0="1001" and s1="0101" and s0="1001" then
qlk<='1';
else
qlk<='0';
end if;
end if;
end process;
end sss_arc;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity MINSECONDb is
port(clk,clrm,stop:in std_logic;----时钟/清零信号
secm1,secm0:out std_logic_vector(3 downto 0);----秒高位/低位
co:out std_logic);-------输出/进位信号
end MINSECONDb;
architecture SEC of MINSECONDb is
signal clk1,DOUT2:std_logic;
begin
process(clk,clrm)
variable cnt1,cnt0:std_logic_vector(3 downto 0);---计数
VARIABLE COUNT2 :INTEGER RANGE 0 TO 10 ;
begin
IF CLK'EVENT AND CLK='1'THEN
IF COUNT2>=0 AND COUNT2<10 THEN
COUNT2:=COUNT2+1;
ELSE COUNT2:=0;
DOUT2<= NOT DOUT2;
END IF;
END IF;
if clrm='1' then----当clr为1时，高低位均为0
cnt1:="0000";
cnt0:="0000";
elsif clk'event and clk='1' then
if stop='1' then
cnt0:=cnt0;
cnt1:=cnt1;
end if;
if cnt1="1001" and cnt0="1000" then----当记数为98（实际是经过59个记时脉冲）
co<='1';----进位
cnt0:="1001";----低位为9
elsif cnt0<"1001" then----小于9时
cnt0:=cnt0+1;----计数
--elsif cnt0="1001" then
--clk1<=not clk1;
else
cnt0:="0000";
if cnt1<"1001" then----高位小于9时
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
secm1<=cnt1;
secm0<=cnt0;
end process;
end SEC;
秒模块程序清单
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity SECOND is
port(clk,clr:in std_logic;----时钟/清零信号
sec1,sec0:out std_logic_vector(3 downto 0);----秒高位/低位
co:out std_logic);-------输出/进位信号
end SECOND;
architecture SEC of SECOND is
begin
process(clk,clr)
variable cnt1,cnt0:std_logic_vector(3 downto 0);---计数
begin
if clr='1' then----当ckr为1时，高低位均为0
cnt1:="0000";
cnt0:="0000";
elsif clk'event and clk='1' then
if cnt1="0101" and cnt0="1000" then----当记数为58（实际是经过59个记时脉冲）
co<='1';----进位
cnt0:="1001";----低位为9
elsif cnt0<"1001" then----小于9时
cnt0:=cnt0+1;----计数
else
cnt0:="0000";
if cnt1<"0101" then----高位小于5时
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
sec1<=cnt1;
sec0<=cnt0;
end process;
end SEC;
分模块程序清单
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity MINUTE is
port(clk,en:in std_logic;
min1,min0:out std_logic_vector(3 downto 0);
co:out std_logic);
end MINUTE;
architecture MIN of MINUTE is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clk'event and clk='1' then
if en='1' then
if cnt1="0101" and cnt0="1000" then
co<='1';
cnt0:="1001";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
else
cnt0:="0000";
if cnt1<"0101" then
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
end if;
min1<=cnt1;
min0<=cnt0;
end process;
end MIN;
时模块程序清单
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity HOUR is
port(clk,en:in std_logic;----输入时钟/高电平有效的使能信号
h1,h0:out std_logic_vector(3 downto 0));----时高位/低位
end HOUR;
architecture hour_arc of HOUR is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);----记数
begin
if clk'event and clk='1' then---上升沿触发
if en='1' then---同时“使能”为1
if cnt1="0010" and cnt0="0011" then
cnt1:="0000";----高位/低位同时为0时
cnt0:="0000";
elsif cnt0<"1001" then----低位小于9时，低位记数累加
cnt0:=cnt0+1;
else
cnt0:="0000";
cnt1:=cnt1+1;-----高位记数累加
end if;
end if;
end if;
h1<=cnt1;
h0<=cnt0;
end process;
end hour_arc;
动态扫描模块
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
use ieee.std_logic_arith.all;
entity SELTIME is
port(
clk:in std_logic;------扫描时钟
secm1,secm0,sec1,sec0,min1,min0,h1,h0:in std_logic_vector(3 downto 0);-----分别为秒个位/时位；分个位/
daout:out std_logic_vector(3 downto 0);----------------输出
sel:out std_logic_vector(2 downto 0));-----位选信号
end SELTIME;
architecture fun of SELTIME is
signal count:std_logic_vector(2 downto 0);----计数信号
begin
sel<=count;
process(clk)
begin
if(clk'event and clk='1') then
if(count>="111") then
count<="000";
else
count<=count+1;
end if;
end if;
case count is
when"111"=>daout<= secm0;----秒个位
when"110"=>daout<= secm1;----秒十位
when"101"=>daout<= sec0;----分个位
when"100"=>daout<= sec1;----分十位
when"011"=>daout<=min0; ----时个位
when"010"=>daout<=min1;----时十位
when"001"=>daout<=h0;
when others =>daout<=h1;
end case;
end process;
end fun;
报时模块
library ieee;
use ieee.std_logic_1164.all;
entity ALERT is
port(m1,m0,s1,s0:in std_logic_vector(3 downto 0);------输入秒、分高/低位信号
clk:in std_logic;------高频声控制
q500,qlk:out std_logic);----低频声控制
end ALERT;
architecture sss_arc of ALERT is
begin
process(clk)
begin
if clk'event and clk='1' then
if m1="0101" and m0="1001" and s1="0101" then----当秒高位为5，低位为9时且分高位为5
if s0="0001" or s0="0011" or s0="0101" or s0="0111" then---当分的低位为1或3或5或7时
q500<='1';----低频输出为1
else
q500<='0';----否则输出为0
end if;
end if;
if m1="0101" and m0="1001" and s1="0101" and s0="1001" then---当秒高位为5，低位为9时且分高位为5，----分低位为9时，也就是“59分59秒”的时候“报时”
qlk<='1';-----高频输出为1
else
qlk<='0';
end if;
end if;
end process;
end sss_arc;
显示模块
library ieee;
use ieee.std_logic_1164.all;
entity DISPLAY is
port(d:in std_logic_vector(3 downto 0);----连接seltime扫描部分d信号
q:out std_logic_vector(6 downto 0));----输出段选信号（电平）
end DISPLAY;
architecture disp_are of DISPLAY is
begin
process(d)
begin
case d is
when"0000" =>q<="0111111";--显示0
when"0001" =>q<="0000110";--显示1
when"0010" =>q<="1011011";--显示2
when"0011" =>q<="1001111";--显示3
when"0100" =>q<="1100110";--显示4
when"0101" =>q<="1101101";--显示5
when"0110" =>q<="1111101";--显示6
when"0111" =>q<="0100111";--显示7
when"1000" =>q<="1111111";--显示8
when others =>q<="1101111";--显示9
end case;
end process;
end disp_are;
顶层文件（原理图输入）
********************************************************************
数字钟设计模块与程序（不含秒表）
*********************************************************************
1.分频模块（原理图输入）
2. 秒模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity SECOND is
port(clk,clr:in std_logic;
sec1,sec0:out std_logic_vector(3 downto 0);
co:out std_logic);
end SECOND;
architecture SEC of SECOND is
begin
process(clk,clr)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clr='1' then
cnt1:="0000";
cnt0:="0000";
elsif clk'event and clk='1' then
if cnt1="0101" and cnt0="1000" then
co<='1';
cnt0:="1001";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
else
cnt0:="0000";
if cnt1<"0101" then
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
sec1<=cnt1;
sec0<=cnt0;
end process;
end SEC;
3.分模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity MINUTE is
port(clk,en:in std_logic;
min1,min0:out std_logic_vector(3 downto 0);
co:out std_logic);
end MINUTE;
architecture MIN of MINUTE is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clk'event and clk='1' then
if en='1' then
if cnt1="0101" and cnt0="1000" then
co<='1';
cnt0:="1001";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
else
cnt0:="0000";
if cnt1<"0101" then
cnt1:=cnt1+1;
else
cnt1:="0000";
co<='0';
end if;
end if;
end if;
end if;
min1<=cnt1;
min0<=cnt0;
end process;
end MIN;
4.时模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
entity HOUR is
port(clk,en:in std_logic;
h1,h0:out std_logic_vector(3 downto 0));
end HOUR;
architecture hour_arc of HOUR is
begin
process(clk)
variable cnt1,cnt0:std_logic_vector(3 downto 0);
begin
if clk'event and clk='1' then
if en='1' then
if cnt1="0010" and cnt0="0011" then
cnt1:="0000";
cnt0:="0000";
elsif cnt0<"1001" then
cnt0:=cnt0+1;
end if;
end if;
end if;
h1<=cnt1;
h0<=cnt0;
end process;
end hour_arc;
5.扫描模块程序
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned.all;
use ieee.std_logic_arith.all;
entity SELTIME is
port(
clk:in std_logic;
sec1,sec0,min1,min0,h1,h0:in std_logic_vector(3 downto 0);
daout:out std_logic_vector(3 downto 0);
sel:out std_logic_vector(2 downto 0));
end SELTIME;
architecture fun of SELTIME is
signal count:std_logic_vector(2 downto 0);
begin
sel<=count;
process(clk)
begin
if(clk'event and clk='1') then
if(count>="101") then
count<="000";
else
count<=count+1;
end if;
end if;
case count is
when"000"=>daout<= sec0;
when"001"=>daout<= sec1;
when"010"=>daout<= min0;
when"011"=>daout<= min1;
when"100"=>daout<=h0;
when others =>daout<=h1;
end case;
end process;
end fun;
6.显示模块程序
library ieee;
use ieee.std_logic_1164.all;
entity DISPLAY is
port(d:in std_logic_vector(3 downto 0);
q:out std_logic_vector(6 downto 0));
end DISPLAY;
architecture disp_are of DISPLAY is
begin
process(d)
begin
case d is
when"0000" =>q<="0111111";
when"0001" =>q<="0000110";
when"0010" =>q<="1011011";
when"0011" =>q<="1001111";
when"0100" =>q<="1100110";
when"0101" =>q<="1101101";
when"0110" =>q<="1111101";
when"0111" =>q<="0100111";
when"1000" =>q<="1111111";
when others =>q<="1101111";
end case;
end process;
end disp_are;
7.定时闹钟模块程序
library ieee;
use ieee.std_logic_1164.all;
entity ALERT is
port(m1,m0,s1,s0:in std_logic_vector(3 downto 0);
clk:in std_logic;
q500,qlk:out std_logic);
end ALERT;
architecture sss_arc of ALERT is
begin
process(clk)
begin
if clk'event and clk='1' then
if m1="0101" and m0="1001" and s1="0101" then
if s0="0001" or s0="0011" or s0="0101" or s0="0111" then
q500<='1';
else
q500<='0';
end if;
end if;
if m1="0101" and m0="1001" and s1="0101" and s0="1001" then
qlk<='1';
else
qlk<='0';
end if;
end if;
end process;
end sss_arc;
基于VHDL语言的自动打铃数字钟设计
其中主体电路完成数字钟的基本功能,扩展电路完成数字钟的扩展功能。论文安排如下: 1、绪论 阐述研究电子钟所具有的现实意义。 2、设计内容及设计方案 论述电子钟的具体设计方案及设计要求。 3、单元电路设计、原理及器件选择 说明电子钟的设计原理以及器件的选择,主要从石英晶体振荡器、分频器、计数器、显示器和校时电...
vhdl数字钟的代码
USE IEEE.STD_LOGIC_1164.ALL;USE IEEE.STD_LOGIC_UNSIGNED.ALL;USE IEEE.STD_LOGIC_ARITH.ALL;entity xsecond is port (clk:in std_logic;clkset:in std_logic;setmin:in std_logic;reset:in std_logic;secout:out std_logic_vector(6 downto 0);enmin:out std_logic );end xsecond;ar...
vhdl数字钟的 CLOCK引脚是啥意思
分配引脚？你要是有开发板的话，都应该有pin assignment file吧，有的话，直接载入，然后把VHDL里的signal 名字改成你需要的信号名（pin assignment file里的）如果没有，自己分配时，要看你的板子上的引脚都怎么与FPGA芯片链接的，然后查pin planner 图，找到正确的pin，比如7 seg LED 一般会连到FPG...
VHDL 数字钟
数字钟设计模块与程序(不含秒表)*** 1.分频模块(原理图输入) 2. 秒模块程序 library ieee;use ieee.std_logic_1164.all;use ieee.std_logic_unsigned.all;entity SECOND isport(clk,clr:in std_logic; sec1,sec0:out std_logic_vector(3 downto 0); co:out std_logic);end SECOND;architecture SEC ...
vhdl 数字钟
vhdl 数字钟 时分秒的数字钟... 时分秒的数字钟 展开 我来答 1个回答 #热议# 《请回答2021》瓜分百万奖金 匿名用户 2009-10-24 展开全部 use ieee.std_logic_1164.all;--顶层实体,用的是20Mhz的时钟use ieee.std_logic_unsigned.all;use ieee.std_logic_arith.all;entity clock_shu is port( ...
VHDL电子时钟设计
基于CPLD的VHDL语言数字钟(含秒表)设计 利用一块芯片完成除时钟源、按键、扬声器和显示器(数码管)之外的所有数字电路功能。所有数字逻辑功能都在CPLD器件上用VHDL语言实现。这样设计具有体积小、设计周期短(设计过程中即可实现时序仿真)、调试方便、故障率低、修改升级容易等特点。本设计采用自顶向下、混合输入方式(原理...
求助~vhdl 数字钟闹钟时间延长到2分钟,用led灯显示。
这个简单，有个使能信号，闹钟开始为1，计数两分钟，然后使能信号为0。把这个使能信号的值赋给led的引脚
基于vhdl电子秒表的系统设计怎么做?
一、实验原理 ：用层次化设计的方法以VHDL语言编程实现以下功能：【1】具有“时”、“分”、“秒”计时功能；时为24进制，分和秒都为60进制。【2】具有消抖功能：手工按下键盘到是否这个过程大概50ms左右，在按下开始到弹簧片稳，定接触这段时间为5-10ms，从释放到弹片完全分开也是5-10ms，在达到...
VHDL数字钟手动调节小时和分怎样实现?
加按键嘛 一个控制时，分的调节模式 一个加，一个减
基于VHDL的数字时钟设计 用VHDL设计EDA数字钟 能显示年月日 时分秒 能...
template class TreeNode{ public:T data;int index;int active;TreeNode & operator=(TreeNode & treenode){ this->data=treenode.data;this->index=treenode.index;this->active=treenode.active;return *this;} };
相似回答
